Plans for Shelf and Drawer Units

A Cute Shelving Unit with a Drawer at the Lesser

If you love the look of open shelving, and so this shelving unit is for you! The DIY plans to build a Milo Shelving Unit feature five open shelves with a large drawer at the lesser. The plans are super-piece of cake to construct and is perfect for all skill levels. The shelving unit of measurement tin be completed in a weekend!

Materials:

• ane-i/four" pocket hole screws (<– affiliate link!)
• 2-1/2" pocket pigsty screws
• Cabinet pulls
• Wood glue
• Sandpaper (100, 150, 220 grits)
• Finishing supplies (primer & paint, or stain, sealer)
• Paste Wax

Lumber:

• 11 – 2×ii at 8′
• 1 – iv′ ten 4′ sail of ¾" plywood
• 1 – 4′ x 8′ sheet of ¾" plywood

Cut Listing:

• iv – two×2 at 76-3/4" – Legs
• 12 – 2×2 at 11" – Side Framing
• 2 – ¾" plywood at xi" x 12-three/four" – Side Panels
• 12 – 2×2 at 39" – Forepart & Back Stretchers
• 1 – ¾" plywood at 12-3/4" x 39" – Back Console
• vi – ¾" plywood at eleven" x 39" – Shelves
• i – ¾" plywood at xi" x 37-3/eight" – Drawer Box Bottom
• 2 – ¾" plywood at 11" x 12-five/8" – Drawer Box Sides
• ii – ¾" plywood at 11" x 38-7/viii" – Drawer Box Front end & Dorsum

Click on the drawings for a larger view!

Step One

Cut the pieces for the legs, the side framing, and the side panels. With the pocket pigsty jig set for one-one/2" cloth, drill pocket holes in each end of the 2×2 pieces. Secure the 2x2s to the legs using glue and 2-1/2" pocket pigsty screws.

Set the pocket hole jig for ¾" textile and drill pocket holes in all iv edges of the panels. Secure the panels to the legs and framing pieces using glue and 1-1/iv" pocket hole screws. The back face of the plywood volition exist flush with the back face up of the legs and framing.

Step Two

Cut the pieces for the stretchers. Set the pocket hole jig for 1-1/two" material and drill pocket holes in each end of the 2×2 pieces. Secure the 2×ii back framing piece to the legs using glue and 2-ane/2" pocket pigsty screws.

Step Three

Cut the piece for the back . Gear up the pocket hole jig for 3/iv″ material and drill pocket holes in all 4 edges. Secure the panel to the legs and stretchers using glue and one-i/4" pocket hole screws. The back confront of the plywood will be flush with the back face up of the legs and framing.

Step Four

Cut the pieces for the shelving and drill pocket holes in all iv edges of each piece. Secure the shelves to the stretchers using glue and 1-one/4″ pocket hole screws. The tiptop face up of the shelves will be flush with the pinnacle edge of each of the corresponding stretchers.

Pace Five

Cut the pieces for the drawer. Drill pocket holes in all four edges of the lesser equally well as each finish of the sides. Secure the sides to the bottom using glue and ane-ane/4" pocket hole screws, then secure the drawer front and dorsum. There will be a 1/16" gap at the sides of the drawer and a 1/8" gap at the superlative of the drawer in the opening.

Finish as desired, then apply a coat of paste wax to the bottom and sides of the drawers to assist them slide smoothly in the openings.

This is a shelving unit of measurement that will be perfect in any room – it would be a great identify to showcase trophies in the family unit room, to store books and toys in a child's room, or equally fabric storage in a craft room! accept whatever questions about the DIY plans to build a Milo Shelving Unit? Leave a annotate below!

etheredgeineder99.blogspot.com

Source: https://designsbystudioc.com/diy-plans-build-milo-shelving-unit/

Bagikan Artikel ini